LAS-M6-2MD
Floating self-clinching, locking thread fasteners LA4, LAC, LAS
LAS-M6-2MD
Floating self-clinching, locking thread fasteners LA4, LAC, LAS
Locking and Non-locking Threads These fasteners provide load-bearing threads in thin sheets and permit up to 0.76mm adjustment for mating hole misalignment.
The self-clinching feature offers fast and simple assembly. The fasteners are squeezed into prepared holes using any standard press. The sheet remains flush on one side, and the fastener is permanently locked in place.
Extra strength and support in assembly is obtained by the threads of the floating nut extending fully into the retainer shank (a unique PEM feature). A self-locking version of the fastener is also offered. Thread locking torque performance is equivalent to applicable NASM25027 specifications.
Non-locking Type A4 and self-locking Type LA4 fasteners provide load-bearing threads in stainless steel sheets as thin as 0.97mm with hardness up to HRB 88 on the Rockwell “B” scale.
Many PEM Type AS and AC self-clinching floating fasteners correspond to sizes in US NASM45938/11 specifications. Check our web site for a complete Military Specification and National Aerospace Standards Reference Guide (Bulletin NASM).
Specifications
- Thread Code
- M6
- Thread Size(x Pitch)
- M6 x 1
- Shank Code
- 2
- Standard Finish – Retainer & Nut
- Zinc Plated, 5μm, Colorless;Black Dry-film Lubricant
- For Use in Sheet Hardness
- HRB 70 / HB 125 or Less
- Float
- 0.38mm minimum, in all directions from center, 0.76mm total
- Product Category
- Floating self-clinching, locking thread fasteners LA4, LAC, LAS – Metric
- Brand
- PEM
- Hole Size in Sheet +.003 / +0.08mm_mm
- 13.08mm
- Locking Performance Cycles
- 15
- PEM Product Family
- LAS
- Product Type
- OtherFasteners
- A Shank Max
- 1.38mm
- E ± 0.38_mm
- 15.24mm
- Hole Size in Sheet + 0.08_mm
- 13.08mm
- Min. Dist. Hole C/L to Edge_mm
- 10.67mm
- C Max._mm
- 13.06mm
- D Max._mm
- 12.96mm
- T2 Max._mm
- 7.88mm
Installation & Performance Data
| Type | Thread Code | Shank Code | Test Sheet Material | A ±.001 (in.) | A ±0.03 (mm) | B ±.005 (in.) | B ±0.13 (mm) | Haeger Part Number Anvil | Haeger Part Number Punch | Installation (kN) | Pemserter Part Number Anvil | Pemserter Part Number Punch | Retainer Pushout (N) | Retainer Torque-out (N•m) | Locknut Min. Axial Strength (kN) | Mating Screw Strength Level (MPa) | Mating Screw Tightening Torque (N•m) | Counterbore A ±.001 (in.) | Counterbore A ±0.03 (mm) | Hole Depth Below Counterbore B ±.005 (in.) | Hole Depth Below Counterbore B ±0.13 (mm) |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| AC-AS-LAC-LAS | M6 | 2 | 5052-H34 Aluminum | 0.092 | 2.34 | 0.315 | 8 | H-131-04L | H-108-0020L | 13.3 | 8021392 | 975200048 | 1779 | 36.7 | |||||||
| AC-AS-LAC-LAS | M6 | 2 | Cold-Rolled Steel | 0.092 | 2.34 | 0.315 | 8 | H-131-04L | H-108-0020L | 22.2 | 8021392 | 975200048 | 2224 | 36.7 | |||||||
| LAC, LAS, LA4 | M6 | 24.55 | 1220 | 19.1 | |||||||||||||||||
| LAS, LAC | M6 | 2 | 2024-T3 Aluminum | H-131-04L | H-108-0020L | 22.2 | 8021392 | 975200048 | 1334 | 36.7 | 0.092 | 2.34 | 0.315 | 8 | |||||||
| LAS, LAC | M6 | 2 | 5052-H34 Aluminum | H-131-04L | H-108-0020L | 13.3 | 8021392 | 975200048 | 1779 | 36.7 | 0.092 | 2.34 | 0.315 | 8 | |||||||
| LAS, LAC | M6 | 2 | Cold-Rolled Steel | H-131-04L | H-108-0020L | 22.2 | 8021392 | 975200048 | 2224 | 36.7 | 0.092 | 2.34 | 0.315 | 8 |
Inventory
| Distributor | Quantity | Contact | Phone | Address | Locations |
|---|